Configuring Brocade ICX-Series Ethernet Switches - Revision history

Digimer: /* Changing a Port's VLAN Assignment */

2016-11-24T07:02:49Z

Changing a Port's VLAN Assignment

Digimer: /* Cabling a pair of ICX6610-24 */

2016-11-24T06:48:07Z

Cabling a pair of ICX6610-24

Digimer: /* VLAN Configuration on the ICX6610-24 */

2016-11-24T06:46:08Z

VLAN Configuration on the ICX6610-24

Show changes

Digimer: /* Forming the VLANs */

2016-11-24T06:22:35Z

Forming the VLANs

← Older revision		Revision as of 06:22, 24 November 2016
Line 1,297:		Line 1,297:

	== Forming the VLANs ==		== Forming the VLANs ==

			{{todo\|1=These are adaptations of output from an ICX6610-48. Redo to capture direct output.}}

			To start, lets take a look at the current VLAN configuration.

			<syntaxhighlight lang="text">
			ICX6610-24 Switch#configure terminal
			ICX6610-24 Switch(config)#show vlan
			</syntaxhighlight>

			<syntaxhighlight lang="text">
			Total PORT-VLAN entries: 1
			Maximum PORT-VLAN entries: 64

			Legend: [Stk=Stack-Id, S=Slot]
			</syntaxhighlight>

			Not much!

			So lets get started.

			=== VLAN Configuration on the ICX6450-24 ===

			{{note\|1=This will apply to any 24-port switch, which is the majority of all installs.}}

			First, we will build the [[BCN]] VLAN, which will use VID 100.

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config)#vlan 100 name bcn
			</syntaxhighlight>

			The BCN spans ports 1 through 10 on both switches, which are expressed as <span class="code">1/1/1</span> to <span class="code">1/1/10</span> and <span class="code">2/1/1</span> to <span class="code">2/1/10</span> for switch 1 and 2, respectively. We can assign these two ranges to this VLAN as one command.

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config-vlan-100)#untag ethernet 1/1/1 to 1/1/10 ethernet 2/1/1 to 2/1/10
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Added untagged port(s) ethe 1/1/1 to 1/1/10 ethe 2/1/1 to 2/1/10 to port-vlan 100.
			</syntaxhighlight>

			The [[SN]] spans ports 11 to 14 on each switch, which are expressed as <span class="code">1/1/11</span> to <span class="code">1/1/14</span> and <span class="code">2/1/11</span> to <span class="code">2/1/14</span> for switch 1 and 2, respectively. We can assign these two ranges to this VLAN as one command as well. First though, we need to define the SN VLAN and switch to it.

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config-vlan-100)#vlan 200 name sn
			ICX6450-24 Switch(config-vlan-200)#untag ethernet 1/1/11 to 1/1/14 ethernet 2/1/11 to 2/1/14
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Added untagged port(s) ethe 1/1/11 to 1/1/14 ethe 2/1/11 to 2/2/14 to port-vlan 200.
			</syntaxhighlight>

			Last, the [[IFN]] spans ports 15 to 24 on each switch, which are expressed as <span class="code">1/1/15</span> to <span class="code">1/1/24</span> and <span class="code">2/1/15</span> to <span class="code">2/1/24</span> for switch 1 and 2, respectively. We can assign these two ranges to this VLAN as one command as well. Again, we need to define the IFN VLAN and switch to it.

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config-vlan-100)#vlan 300 name ifn
			ICX6450-24 Switch(config-vlan-300)#untag ethernet 1/1/15 to 1/1/24 ethernet 2/1/15 to 2/1/24
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Added untagged port(s) ethe 1/1/15 to 1/1/24 ethe 2/1/15 to 2/1/24 to port-vlan 300.
			</syntaxhighlight>

			Done! Exit out of the VLAN configuration:

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config-vlan-300)#exit
			</syntaxhighlight>

			Let's see what it looks like now:

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config)#show vlan
			</syntaxhighlight>

			<syntaxhighlight lang="text">
			Total PORT-VLAN entries: 4
			Maximum PORT-VLAN entries: 64

			Legend: [Stk=Stack-Id, S=Slot]

			PORT-VLAN 1, Name DEFAULT-VLAN, Priority level0, Spanning tree On
			Untagged Ports: None
			Tagged Ports: None
			Uplink Ports: None
			DualMode Ports: None
			Mac-Vlan Ports: None
			Monitoring: Disabled
			PORT-VLAN 100, Name bcn, Priority level0, Spanning tree On
			Untagged Ports: (U1/M1) 1 2 3 4 5 6 7 8 9 10
			Untagged Ports: (U2/M1) 1 2 3 4 5 6 7 8 9 10
			Tagged Ports: None
			Uplink Ports: None
			DualMode Ports: None
			Mac-Vlan Ports: None
			Monitoring: Disabled
			PORT-VLAN 200, Name sn, Priority level0, Spanning tree On
			Untagged Ports: (U1/M3) 11 12 13 14
			Untagged Ports: (U2/M3) 11 12 13 14
			Tagged Ports: None
			Uplink Ports: None
			DualMode Ports: None
			Mac-Vlan Ports: None
			Monitoring: Disabled
			PORT-VLAN 300, Name ifn, Priority level0, Spanning tree On
			Untagged Ports: (U1/M1) 15 16 17 18 19 20 21 22 23 24
			Untagged Ports: (U2/M1) 15 16 17 18 19 20 21 22 23 24
			Tagged Ports: None
			Uplink Ports: None
			DualMode Ports: None
			Mac-Vlan Ports: None
			Monitoring: Disabled
			</syntaxhighlight>

			Perfectly perfect. Save the changes and then we're done.

			<syntaxhighlight lang="text">
			ICX6450-24 Switch(config)#write memory
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Write startup-config done.

			Automatic copy to member units: 2
			Flash Memory Write (8192 bytes per dot) .
			Flash to Flash Done.
			</syntaxhighlight>

			Done!

			=== VLAN Configuration on the ICX6610-24 ===




	{{footer}}		{{footer}}

Digimer: /* Port Assignment */

2016-11-24T02:14:18Z

Port Assignment

← Older revision		Revision as of 02:14, 24 November 2016
Line 801:		Line 801:
	{{warning\|1=Test fragmentless pings between all node and dashboard interfaces before starting the ''Anvil!'' system! If anything is misconfigured and the requested MTU is not working, the cluster can break!}}		{{warning\|1=Test fragmentless pings between all node and dashboard interfaces before starting the ''Anvil!'' system! If anything is misconfigured and the requested MTU is not working, the cluster can break!}}

	= ~~Port Assignment~~ =		= Configure VLAN =

			[[VLAN]]s provide a way of dividing up a switch (or stack of switches) into multiple, isolated switches (this is actually somewhat simplistic, but it gets the idea across). Traffic from one VLAN segment can not reach ports allocated to another VLAN, providing a useful layer of security.

			== Planning ==

	{{note\|1=You could use a 48-port switch to host five ''Anvil!'' pairs, but it is '''NOT''' recommended. An important part of [[Intelligent Availability]] is to distribute risk. Multiple two-pair foundation packs serves that purpose best.}}		{{note\|1=You could use a 48-port switch to host five ''Anvil!'' pairs, but it is '''NOT''' recommended. An important part of [[Intelligent Availability]] is to distribute risk. Multiple two-pair foundation packs serves that purpose best.}}

			We're creating three separate [[VLAN]]s;
			* [[VLAN]] ID: <span class="code">100</span> for the [[BCN]].
			* [[VLAN]] ID: <span class="code">200</span> for the [[SN]].
			* [[VLAN]] ID: <span class="code">300</span> for the ([[IFN]].

			By default, all ports default to [[VID]] <span class="code">1</span>. If you want to improve security, you can leave all unused ports on VID <span class="code">1</span>. In this tutorial, we need to allocate all ports for use by other equipment.

			Before you start, you need to decide how you want to assign physical ports on your switches to VLAN IDs. I like to do this by creating a table showing all the ports, label their external port numbers and logical numbers and then write in what will be plugged into each port. With this, it's fairly easy to mark what ports will be assigned to what VLANs.

	We will cover the port assignments for two scenarios;		We will cover the port assignments for two scenarios;
Line 810:		Line 823:
	#. Using the 10 Gbps ports on the ICX6610 to support one ''Anvil!'' node pair operating at 10 Gbps.		#. Using the 10 Gbps ports on the ICX6610 to support one ''Anvil!'' node pair operating at 10 Gbps.

	== ICX6450-24 ~~(Applies to all 24-port switches)~~ ==		=== Cabling a pair of ICX6450-24 ===

	In this example, we're showing how to cable up a pair of [http://www.brocade.com/products/all/switches/product-details/icx-6430-and-6450-switches/specifications.page ICX6450-24] switches in a very typical configuration. It can drive two [[Anvil!]] systems along with the usual foundation pack.		In this example, we're showing how to cable up a pair of [http://www.brocade.com/products/all/switches/product-details/icx-6430-and-6450-switches/specifications.page ICX6450-24] switches in a very typical configuration. It can drive two [[Anvil!]] systems along with the usual foundation pack.
Line 980:		Line 993:
	\|}		\|}

	== ICX6610-24 ~~(8x 10 Gbps, 24x 1 Gbps)~~ ==		=== Cabling a pair of ICX6610-24 ===

	In this example, we're showing how to cable up a pair of [http://www.brocade.com/products/all/switches/product-details/icx-6610-switch/specifications.page ICX6610-48] switches in a rather unusual configuration. It is driving three [[Anvil!]] pairs. However, only the first is running at 10 Gbps while the second and third pair are running at 1 Gbps.		In this example, we're showing how to cable up a pair of [http://www.brocade.com/products/all/switches/product-details/icx-6610-switch/specifications.page ICX6610-48] switches in a rather unusual configuration. It is driving three [[Anvil!]] pairs. However, only the first is running at 10 Gbps while the second and third pair are running at 1 Gbps.
Line 1,282:		Line 1,295:
	mgmt1 Down None None None None No None 0 cc4e.24b9.4b74		mgmt1 Down None None None None No None 0 cc4e.24b9.4b74
	</syntaxhighlight>		</syntaxhighlight>

			== Forming the VLANs ==



	{{footer}}		{{footer}}

Digimer: /* Enable Jumbo Frames */

2016-11-24T02:10:44Z

Enable Jumbo Frames

Show changes

Digimer: /* Port Assignment */

2016-11-24T02:10:28Z

Port Assignment

Show changes

Digimer: /* Form the Stack */

2016-11-23T05:11:45Z

Form the Stack

Show changes

Digimer: /* Update the firmware */

2016-11-23T04:59:56Z

Update the firmware

← Older revision		Revision as of 04:59, 23 November 2016
Line 577:		Line 577:

	Once it comes back up, your switch will be as-new.		Once it comes back up, your switch will be as-new.

			= Assign IP to Switch =

			{{note\|1=In order to update the firmware or load licenses, you will need to be able to access the switch via an IP address.}}

			Log into the switch over serial and switch to the configuration terminal:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch#configure terminal
			</syntaxhighlight>

			Assign the IP address and subnet mask to the switch:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch(config)#ip address 10.20.1.1 255.255.0.0
			</syntaxhighlight>

			Exit the configuration terminal:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch(config)#exit
			</syntaxhighlight>

			{{note\|1=Our router is at <span class="code">10.20.255.254</span>, which is what we will ping here. You can choose any target device on the same subnet instead.}}

			Test by pinging an external device on the same subnet:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch#ping 10.20.255.254
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Sending 1, 16-byte ICMP Echo to 10.20.255.254, timeout 5000 msec, TTL 64
			Type Control-c to abort
			Reply from 10.20.255.254 : bytes=16 time<1ms TTL=64
			Success rate is 100 percent (1/1), round-trip min/avg/max=0/0/0 ms.
			</syntaxhighlight>

			Good, save the changes:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch#write memory
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Write startup-config done.

			Automatic copy to member units: 2
			Flash Memory Write (8192 bytes per dot) .
			Flash to Flash Done.
			</syntaxhighlight>

			Done!

	= Update the firmware =		= Update the firmware =

Digimer: /* Form the Stack */

2016-11-23T04:57:18Z

Form the Stack

← Older revision		Revision as of 04:57, 23 November 2016
Line 963:		Line 963:

	Excellent, done!		Excellent, done!

			= Enable Jumbo Frames =

			{{note\|1=The ICX6610 support packets up to 10,240 [[bytes]] (10 [[KiB]]) and the ICX6450 supports 9,216 bytes (9 KiB). That is to say, if jumbo frames are enabled, the [[MTU]] of the switch is 9 or 10 [[KiB]], depending on the model.}}

			Jumbo frames are a way to increase performance on a network by allowing more data in a packet's payload, increasing transmission efficiency and reducing the number of packets needed for a given transmission. To work, however, you must be aware of the maximum transmission size of your network interfaces, switches and all other devices between your machine and the receiver. If you enable large MTUs (called "jumbo frames"), be certain to test that you really can use the requested MTU!

			The easiest way to do this is to ping the remote machine(s) using '<span class="code">ping -M do -s X</span>', where 'X' is the desired MTU, minus 28 bytes for packet overhead. That is to say, if you set your MTU to '9216', test by pinging the target with '<span class="code">ping -M do -s 9188</span>'. See the manual page for 'ping' for more information.

			Connect to the switch, log in and enter the configuration terminal:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch#configure terminal
			</syntaxhighlight>

			Enable jumbo frames:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch(config)#jumbo
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Jumbo mode setting requires a reload to take effect!
			</syntaxhighlight>

			Save the changes:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch(config)#write memory
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Write startup-config done.

			Automatic copy to member units: 2
			Flash Memory Write (8192 bytes per dot) .
			Flash to Flash Done.
			</syntaxhighlight>

			Exit the configuration terminal:

			<syntaxhighlight lang="text">
			ICX6610-48 Switch(config)#exit
			</syntaxhighlight>

			Finally, reboot the switch.

			<syntaxhighlight lang="text">
			ICX6610-48 Switch#reload
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Are you sure? (enter 'y' or 'n'): y
			</syntaxhighlight>
			<syntaxhighlight lang="text">
			Reload request sent to attached stack member(s)...

			Rebooting(0)...
			</syntaxhighlight>

			{{warning\|1=Test fragmentless pings between all node and dashboard interfaces before starting the ''Anvil!'' system! If anything is misconfigured and the requested MTU is not working, the cluster can break!}}


	{{footer}}		{{footer}}

← Older revision		Revision as of 06:48, 24 November 2016
Line 1,021:		Line 1,021:
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; background-color: #2f2f2f; color: #cfcfcf; text-align: center;" colspan="4"\|Internet-Facing Network		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; background-color: #2f2f2f; color: #cfcfcf; text-align: center;" colspan="4"\|Internet-Facing Network
	\|-		\|-
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL1 (1/3/1)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL1 (1/2/1)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL2-5 (1/3/2~5)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL2-5 (1/2/2~5)
	\|rowspan="2"\|		\|rowspan="2"\|
	\|rowspan="2"\|		\|rowspan="2"\|
Line 1,059:		Line 1,059:
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|--		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|--
	\|-		\|-
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL6 (1/3/6)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL6 (1/2/6)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL7~10 (1/3/7~10)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL7~10 (1/2/7~10)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X1 (1/2/1)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X1 (1/3/1)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X2 (1/2/2)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X2 (1/3/2)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f8f7f; text-align: center;"\|X3 (1/2/3)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f8f7f; text-align: center;"\|X3 (1/3/3)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X4 (1/2/4)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X4 (1/3/4)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X5 (1/2/5)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X5 (1/3/5)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X6 (1/2/6)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X6 (1/3/6)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X7 (1/2/7)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X7 (1/3/7)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X8 (1/2/8)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X8 (1/3/8)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|2 (1/1/2)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|2 (1/1/2)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|4 (1/1/4)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|4 (1/1/4)
Line 1,137:		Line 1,137:
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; background-color: #2f2f2f; color: #cfcfcf; text-align: center;" colspan="4"\|Internet-Facing Network		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; background-color: #2f2f2f; color: #cfcfcf; text-align: center;" colspan="4"\|Internet-Facing Network
	\|-		\|-
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL1 (2/3/1)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL1 (2/2/1)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL2-5 (2/3/2~5)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|XL2-5 (2/2/2~5)
	\|rowspan="2"\|		\|rowspan="2"\|
	\|rowspan="2"\|		\|rowspan="2"\|
Line 1,175:		Line 1,175:
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #000000; text-align: center;"\|Maintenance		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #000000; text-align: center;"\|Maintenance
	\|-		\|-
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL6 (2/3/6)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL6 (2/2/6)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL7~10 (2/3/7~10)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|XL7~10 (2/2/7~10)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X1 (2/2/1)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X1 (2/3/1)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X2 (2/2/2)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X2 (2/3/2)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f8f7f; text-align: center;"\|X3 (2/2/3)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f8f7f; text-align: center;"\|X3 (2/3/3)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X4 (2/2/4)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X4 (2/3/4)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X5 (2/2/5)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X5 (2/3/5)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X6 (2/2/6)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X6 (2/3/6)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X7 (2/2/7)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #5f5f5f; text-align: center;"\|X7 (2/3/7)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X8 (2/2/8)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|X8 (2/3/8)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|2 (2/1/2)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|2 (2/1/2)
	\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|4 (2/1/4)		\|style="font-family: 'Dejavu Sans Mono', 'Courier 10 pitch', monospace, Courier; font-size: 12px; white-space: nowrap; color: #7f7f7f; text-align: center;"\|4 (2/1/4)