D-Link Notes - Revision history

Digimer at 20:51, 1 December 2023

2023-12-01T20:51:12Z

← Older revision		Revision as of 20:51, 1 December 2023
Line 8:		Line 8:

	{{warning\|1=Make sure the switches are powered by a UPS before doing firmware updates!}}		{{warning\|1=Make sure the switches are powered by a UPS before doing firmware updates!}}

			{{note\|1=It is strongly recommended to update firmware on switches while outside of the stack. Get all switches to the same version before forming a stack.}}

	Setup a TFTP server and made the firmware update available there. In this example, the [[TFTP server]] will be <span class="code">10.201.255.254</span>.		Setup a TFTP server and made the firmware update available there. In this example, the [[TFTP server]] will be <span class="code">10.201.255.254</span>.
Line 48:		Line 50:
	<syntaxhighlight lang="text">		<syntaxhighlight lang="text">
	DGS-3120-24TC:admin#reboot		DGS-3120-24TC:admin#reboot
			</syntaxhighlight>

			<syntaxhighlight lang="text">
			Are you sure you want to proceed with the system reboot?(y/n)
	</syntaxhighlight>		</syntaxhighlight>

Digimer at 20:20, 1 December 2023

2023-12-01T20:20:24Z

← Older revision		Revision as of 20:20, 1 December 2023
Line 4:		Line 4:

	= DGS-3120 Series =		= DGS-3120 Series =

			== Update Firmware ==

			{{warning\|1=Make sure the switches are powered by a UPS before doing firmware updates!}}

			Setup a TFTP server and made the firmware update available there. In this example, the [[TFTP server]] will be <span class="code">10.201.255.254</span>.

			From the admin console:

			<syntaxhighlight lang="text">
			DGS-3120-24TC:admin# download firmware_fromTFTP 10.201.255.254 src_file FW_300022.had dest_file FW_300022.had
			</syntaxhighlight>

			This will take a while to download.

			<syntaxhighlight lang="text">
			Command: download firmware_fromTFTP 10.201.255.254 src_file FW_300022.had dest_file FW_300022.had

			Connecting to server................... Done.
			Download firmware...................... Done. Do not power off!
			Please wait, programming flash......... Done.


			DGS-3120-24TC:admin#
			</syntaxhighlight>

			Now tell it to boot <span class="code">FW_300022.had</span> on the next boot.

			<syntaxhighlight lang="text">
			config firmware image unit 1 FW_300022.had boot_up
			</syntaxhighlight>

			{{note\|1=When stacked, you only need to specify 'unit 1'.}}

			<syntaxhighlight lang="text">
			Command: config firmware image unit 1 FW_300022.had boot_up

			Success.
			</syntaxhighlight>

			Now reboot.

			<syntaxhighlight lang="text">
			DGS-3120-24TC:admin#reboot
			</syntaxhighlight>

			When back up, it's done.

			== Configure ==

	# Ensure you've updated the [http://www.dlink.ca/products/?pid=DGS-3120-24TC firmware] to <span class="code">[ftp://ftp.dlink.com/Switch/dgs3120series/Firmware/dgs3120series_FW_200010.zip R2.00.010]</span> or higher.		# Ensure you've updated the [http://www.dlink.ca/products/?pid=DGS-3120-24TC firmware] to <span class="code">[ftp://ftp.dlink.com/Switch/dgs3120series/Firmware/dgs3120series_FW_200010.zip R2.00.010]</span> or higher.

Digimer at 00:00, 10 July 2012

2012-07-10T00:00:45Z

← Older revision		Revision as of 00:00, 10 July 2012
Line 33:		Line 33:
	## '<span class="code">Save</span>' -> '<span class="code">Save Configuration / Log</span>'.		## '<span class="code">Save</span>' -> '<span class="code">Save Configuration / Log</span>'.
	## Change '<span class="code">Type</span>' to "<span class="code">All</span>" and click '<span class="code">Apply</span>'.		## Change '<span class="code">Type</span>' to "<span class="code">All</span>" and click '<span class="code">Apply</span>'.

			* Thanks to [http://dk.linkedin.com/in/fabbione Fabio Massimo Di Nitto] for helping to sort out this recipe!

	{{footer}}		{{footer}}

Digimer at 23:50, 9 July 2012

2012-07-09T23:50:53Z

← Older revision		Revision as of 23:50, 9 July 2012
Line 5:		Line 5:
	= DGS-3120 Series =		= DGS-3120 Series =

	~~Confirmed~~		# Ensure you've updated the [http://www.dlink.ca/products/?pid=DGS-3120-24TC firmware] to <span class="code">[ftp://ftp.dlink.com/Switch/dgs3120series/Firmware/dgs3120series_FW_200010.zip R2.00.010]</span> or higher.
	# Ensure you've updated the firmware to R2.00.010 or higher		# Make the stacking master static;
	# System Configuration -> Stacking -> Stacking Mode Settings. Change 'Force Master Role' to 'Enabled'.		## <span class="code">System Configuration</span> -> <span class="code">Stacking</span> -> <span class="code">Stacking Mode Settings</span>.
	# System Configuration -> Port Configuration -> Port Settings. Set 'Flow Control' to 'Enabled' for all ports on both switches.		## Change '<span class="code">Force Master Role</span>' to '<span class="code">Enabled</span>'.
			# Enable flow-control;
			## <span class="code">System Configuration</span> -> <span class="code">Port Configuration</span> -> <span class="code">Port Settings</span>.
			## Set '<span class="code">Flow Control</span>' to '<span class="code">Enabled</span>' for all ports on both switches.
	## Confirm with <span class="code">dmesg \|grep -i flow</span> and look for <span class="code">e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx</span>. If any interfaces show <span class="code">Flow Control: None</span>, it's not setup right.		## Confirm with <span class="code">dmesg \|grep -i flow</span> and look for <span class="code">e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx</span>. If any interfaces show <span class="code">Flow Control: None</span>, it's not setup right.
	# Setup ~~VLANs~~ for the SN and IFN (leave the BCN on the default VID 1).		# Setup [[VLAN]]s for the [[SN]] and [[IFN]] (leave the [[BCN]] on the default [[VID]] <span class="code">1</span>).
	## L2 Features -> VLAN -> 802.1Q VLAN Settings		## L2 Features -> VLAN -> 802.1Q VLAN Settings
	## For each VLAN; Click "Add/Edit VLAN" tab -> Enter a unique VID (100 for SN, 101 for IFN), Set a unique VLAN name. Change the ports in the VLAN to the 'untagged' radio button and leave the rest as 'Not Member'. Leave 'Advertisement' as 'Disabled'. Click 'Apply' and repeat for the other VLAN.		## For each VLAN;
	# Setup a static trunk for the two uplink ports; L2 Features -> Link Aggregation -> Port Trunking Settings.		### Click '<span class="code">Add/Edit VLAN</span>' tab.
	## Use 'MAC Source' algorithm~~, set~~ the ~~group ID, use~~ 'Type' of "Static"~~, set~~ the master port (usually 1:24)~~, change~~ 'State' to "Enabled" ~~and tick~~ to enable the appropriate ports (usually 1:24 and 2:24).		### Enter a unique [[VID]] (<span class="code">100</span> for [[SN]], <span class="code">101</span> for [[IFN]]).
			### Set a unique VLAN name.
			### Change the ports in the VLAN to the '<span class="code">untagged</span>' radio button and leave the rest as '<span class="code">Not Member</span>'.
			### Leave '<span class="code">Advertisement</span>' as '<span class="code">Disabled</span>'.
			### Click '<span class="code">Apply</span>' and repeat for the other VLAN.
			# Setup a static trunk for the two uplink ports;
			## <span class="code">L2 Features</span> -> <span class="code">Link Aggregation</span> -> <span class="code">Port Trunking Settings</span>.
			## Use '<span class="code">MAC Source</span>' algorithm.
			## Set a unique <span class="code">Group ID</span>.
			## Set the '<span class="code">Type</span>' of "<span class="code">Static</span>".
			## Set the master port (usually <span class="code">1:24</span>).
			## Change '<span class="code">State</span>' to "<span class="code">Enabled</span>".
			## Check to enable the appropriate ports (usually <span class="code">1:24</span> and <span class="code">2:24</span>).
	# Save your changes!		# Save your changes!
	## 'Save' -> 'Save Configuration / Log'. Change 'Type' to "All" and click 'Apply'.		## '<span class="code">Save</span>' -> '<span class="code">Save Configuration / Log</span>'.
			## Change '<span class="code">Type</span>' to "<span class="code">All</span>" and click '<span class="code">Apply</span>'.

	{{footer}}		{{footer}}

Digimer at 21:02, 9 July 2012

2012-07-09T21:02:55Z

← Older revision		Revision as of 21:02, 9 July 2012
Line 8:		Line 8:
	# Ensure you've updated the firmware to R2.00.010 or higher		# Ensure you've updated the firmware to R2.00.010 or higher
	# System Configuration -> Stacking -> Stacking Mode Settings. Change 'Force Master Role' to 'Enabled'.		# System Configuration -> Stacking -> Stacking Mode Settings. Change 'Force Master Role' to 'Enabled'.

	~~Testing~~
	# System Configuration -> Port Configuration -> Port Settings. Set 'Flow Control' to 'Enabled' for all ports on both switches.		# System Configuration -> Port Configuration -> Port Settings. Set 'Flow Control' to 'Enabled' for all ports on both switches.
	## Confirm with <span class="code">dmesg \|grep -i flow</span> and look for <span class="code">e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx</span>. If any interfaces show <span class="code">Flow Control: None</span>, it's not setup right.		## Confirm with <span class="code">dmesg \|grep -i flow</span> and look for <span class="code">e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx</span>. If any interfaces show <span class="code">Flow Control: None</span>, it's not setup right.
	# ~~Create~~ VLANs for the ~~bonds, 'untagged', disable advertisement~~ (~~666~~ for SN, 71 for IFN, ~~default/1~~ for ~~BCN)~~.		# Setup VLANs for the SN and IFN (leave the BCN on the default VID 1).
	# Setup ~~Trunking~~; L2 Features -> Link Aggregation -> Port Trunking Settings. ~~Set~~ 'Type' to '~~Static~~' and ~~set switch~~ 1 ~~port X as the master~~. ~~Create a trunk for each node~~'~~s bond~~.		## L2 Features -> VLAN -> 802.1Q VLAN Settings
			## For each VLAN; Click "Add/Edit VLAN" tab -> Enter a unique VID (100 for SN, 101 for IFN), Set a unique VLAN name. Change the ports in the VLAN to the 'untagged' radio button and leave the rest as 'Not Member'. Leave 'Advertisement' as 'Disabled'. Click 'Apply' and repeat for the other VLAN.
			# Setup a static trunk for the two uplink ports; L2 Features -> Link Aggregation -> Port Trunking Settings.
			## Use 'MAC Source' algorithm, set the group ID, use 'Type' of "Static", set the master port (usually 1:24), change 'State' to "Enabled" and tick to enable the appropriate ports (usually 1:24 and 2:24).
			# Save your changes!
			## 'Save' -> 'Save Configuration / Log'. Change 'Type' to "All" and click 'Apply'.

	{{footer}}		{{footer}}

Digimer at 19:11, 9 July 2012

2012-07-09T19:11:30Z

← Older revision		Revision as of 19:11, 9 July 2012
Line 1:		Line 1:
	{{header}}		{{header}}

	Notes on setting up D-Link switches.		Notes on setting up D-Link switches for high availabilty.

	= DGS-3120 Series =		= DGS-3120 Series =

			Confirmed
	# Ensure you've updated the firmware to R2.00.010 or higher		# Ensure you've updated the firmware to R2.00.010 or higher
	# System Configuration -> Stacking -> Stacking Mode Settings. Change 'Force Master Role' to 'Enabled'.		# System Configuration -> Stacking -> Stacking Mode Settings. Change 'Force Master Role' to 'Enabled'.

			Testing
			# System Configuration -> Port Configuration -> Port Settings. Set 'Flow Control' to 'Enabled' for all ports on both switches.
			## Confirm with <span class="code">dmesg \|grep -i flow</span> and look for <span class="code">e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx</span>. If any interfaces show <span class="code">Flow Control: None</span>, it's not setup right.
			# Create VLANs for the bonds, 'untagged', disable advertisement (666 for SN, 71 for IFN, default/1 for BCN).
			# Setup Trunking; L2 Features -> Link Aggregation -> Port Trunking Settings. Set 'Type' to 'Static' and set switch 1 port X as the master. Create a trunk for each node's bond.


	{{footer}}		{{footer}}

Digimer: Created page with "{{header}} Notes on setting up D-Link switches. = DGS-3120 Series = # Ensure you've updated the firmware to R2.00.010 or higher # System Configuration -> Stacking -> Stacking ..."

2012-07-06T23:13:13Z

Created page with "{{header}} Notes on setting up D-Link switches. = DGS-3120 Series = # Ensure you've updated the firmware to R2.00.010 or higher # System Configuration -> Stacking -> Stacking ..."

Páàjì titun

{{header}}

Notes on setting up D-Link switches.

= DGS-3120 Series =

# Ensure you've updated the firmware to R2.00.010 or higher
# System Configuration -> Stacking -> Stacking Mode Settings. Change 'Force Master Role' to 'Enabled'.

{{footer}}