Changes
Jump to navigation
Jump to search
Track the most recent changes to the wiki on this page.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
30 March 2024
|
02:30 | Configuring D-Link Switches 2 changes history +3,867 [Digimer (2×)] | |||
|
02:30 (cur | prev) +487 Digimer talk contribs (→Enable Flow Control) | ||||
|
02:19 (cur | prev) +3,380 Digimer talk contribs (→Configure an IP address) |
29 March 2024
|
N 22:48 | Configuring D-Link Switches 4 changes history +2,938 [Digimer (4×)] | |||
|
22:48 (cur | prev) +129 Digimer talk contribs (→Configure an IP address) | ||||
|
22:43 (cur | prev) +45 Digimer talk contribs (→Configure an IP address) | ||||
|
22:41 (cur | prev) +400 Digimer talk contribs | ||||
N |
|
21:53 (cur | prev) +2,364 Digimer talk contribs (Created page with "{{howto_header}} = Validated Switches = The following switches (and firmwares) have been validates to work with the Anvil!: * DGS-3130-series Other models will be similar, but this is the tested model. = Serial Connection = {{note|1=Depending on your terminal emulator, the <span class="code"><Backspace></span> key may not work. If it doesn't, try pressing <span class="code">ctrl + h</span> to delete the character to the left of your cursor.}} You can use <span cl...") |
N 20:12 | Ethernet Switch Configuration diffhist +824 Digimer talk contribs (Created page with "{{howto_header}} The Anvil! is agnostic on ethernet switches. The only requirements is that there are two switches, that VLAN traffic can flow between them, and that one switch doesn't get interrupted when the peer switch connects, disconnects, or gets replaced. Ideally, each switch should have redundant power. If this is not possible, split the first switch to run off the first UPS or PDU, and the second switch to run off the other UPS and PDU. Ideally, setup...") |
28 March 2024
|
N 05:00 | Nftables Router Tutorial 8 changes history +17,365 [Digimer (8×)] | |||
|
05:00 (cur | prev) +2,432 Digimer talk contribs | ||||
|
04:44 (cur | prev) +11,769 Digimer talk contribs | ||||
|
01:44 (cur | prev) +675 Digimer talk contribs (→Setup) | ||||
|
01:31 (cur | prev) +1,176 Digimer talk contribs | ||||
|
01:05 (cur | prev) +735 Digimer talk contribs | ||||
|
00:34 (cur | prev) +140 Digimer talk contribs | ||||
|
00:27 (cur | prev) 0 Digimer talk contribs | ||||
N |
|
00:26 (cur | prev) +438 Digimer talk contribs (Created page with "{{howto_header}} This tutorial is meant to show how to use <span class="code">nftables</span> to build a router suitable for a home or boat. = References = *[Getting started with nftables https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/9/html/configuring_firewalls_and_packet_filters/getting-started-with-nftables_firewall-packet-filters] (required a Red Hat account). <span class="code"></span> {{footer}}") |